dual output +vo pfm isolation ref.amp lc filter +vin -vin com. -vo single output pfm isolation ref.amp lc filter +vin -vin -vo +vo block diagram wide range 2:1 en55022 emi i/o isolation 1500 vdc low cost $ minmax's miw1500-series power modules operate over input voltage ranges of 4.5-9vdc, 9-18vdc and 18-36vdc which provide precisely regulated output voltages of 5v, 12v, {12v and {15vdc. the -25] to +71] operating temperature range makes it ideal for data communication equipments, mobile battery driven equipments, distributed power systems, telecommunication equipments, mixed analog/digital subsystems, process/machine control equipments, computer per ipheral systems and industrial robot systems. the modules have a maximum power rating of 3w and a typical full-load efficiency of 82%, cont inuous short circuit, 45ma output ripple, en55022 class a conduct ed noise compliance minimize design-in time, cost and eliminate the need for external filtering. y industry standard pinout y internal smd construction y ul 94v-0 package material y temperature performance -25] to +71] y complies with en55022 class a y low cost y 2:1 wide input range y mtbf > 1,000,000 hours y 1500vdc isolation y efficiency up to 82% key features 3w, wide input range dip, single & dual output dc/dc converters miw1500 series rev:0 2005/04 minmax 1
82 152 {10 {100 {15 miw1537 82 152 {12.5 {125 {12 miw1536 82 152 25 250 12 miw1533 78 15 5 160 60 600 5 24 ( 18 ~ 36 ) miw1532 80 313 {10 {100 {15 miw1527 80 313 {12.5 {125 {12 miw1526 80 313 25 250 12 miw1523 76 30 20 329 60 600 5 12 ( 9 ~ 18 ) miw1522 77 779 {10 {100 {15 miw1517 77 779 {12.5 {125 {12 miw1516 76 789 25 250 12 miw1513 72 100 40 833 60 600 5 5 ( 4.5 ~ 9 ) miw1512 % (typ.) ma (typ.) ma (typ.) ma (typ.) ma ma vdc vdc @max. load @no load @max. load min. max. efficiency reflected ripple current input current output current output voltage input voltage model number model selection guide en55022 class a conducted emi free-air convection cooling % 95 --- humidity ] +125 -40 storage temperature ] +90 -25 case operating temperature ] +71 -25 ambient operating temperature unit max. min. conditions parameter environmental specifications exceeding the absolute maximum rati ngs of the unit could cause damage. these are not conti nuous operating ratings. mw 2,500 --- internal power dissipation ] 260 --- lead temperature (1.5mm from case for 10 sec.) vdc 50 -0.7 24vdc input models vdc 25 -0.7 12vdc input models vdc 11 -0.7 5vdc input models input surge voltage ( 1000 ms ) unit max. min. parameter notes : 1. specifications typical at ta=+25], resistive load, nominal input voltage, rated output current unless otherwise noted. 2. transient recovery time is measured to within 1% error band for a step change in output load of 75% to 100%. 3. ripple & noise measurement bandwidth is 0-20 mhz. 4. these power converte rs require a minimum output loading to maintain specified regulation. 5. operation under no-load conditions will not damage these modules; however, they may not meet all specifications listed. 6. all dc/dc converters s hould be externally fused at the front end for protection. 7. other input and output voltage may be available, please contact factory. 8. specifications subjec t to change without notice. absolute maximum ratings miw1500 series 2 minmax rev:0 2005/04
k hours --- --- 1000 mil-hdbk-217f @ 25], ground benign mtbf khz --- 300 --- switching frequency pf 500 --- --- 100khz,1v isolation capacitance m[ --- --- 1000 500vdc isolation resistance vdc --- --- 1650 flash tested for 1 second isolation voltage test vdc --- --- 1500 60 seconds isolation voltage rated unit max. typ. min. conditions parameter general specifications continuous output short circuit %/] {0.02 {0.01 --- temperature coefficient % {6 {3 --- transient response deviation us 500 300 --- 25% load step change transient recovery time % --- --- 120 over power protection mv rms 15 --- --- ripple & noise (20mhz) mv p-p 100 --- --- over line, load & temp. ripple & noise (20mhz) mv p-p 60 45 --- ripple & noise (20mhz) % {0.5 {0.2 --- io=10% to 100% load regulation % {0.5 {0.2 --- vin=min. to max. line regulation % {2.0 {0.5 --- dual output, balanced loads output voltage balance % {2.0 {0.5 --- output voltage accuracy unit max. typ. min. conditions parameter output specifications pi filter input filter mw 2000 1000 --- short circuit input power a 1 --- --- all models reverse polarity input current 17 11 --- 24v input models 8.5 6.5 --- 12v input models 4 3.5 --- 5v input models under voltage shutdown 18 12 8 24v input models 9 7 4.5 12v input models vdc 4.5 4 3.5 5v input models start voltage unit max. typ. min. model parameter input specifications # for each output uf 220 220 470 470 maximum capacitive load unit {15v # {12v # 12v 5v models by vout capacitive load miw1500 series rev:0 2005/04 minmax 3
350ma slow - blow type 700ma slow - blow type 1500ma slow - blow type 24v input models 12v input models 5v input models input fuse selection guide vin ( vdc ) 10us 150 140 130 120 110 100 90 80 70 60 100us 1ms 10ms 100ms 50 40 30 20 10 0 24vdc input models 12vdc input models 5vdc input models input voltage transient rating miw1500 series 4 minmax rev:0 2005/04
derating curve ? ] ambient temperature output power (%) 0 20 40 60 80 100 -25 50 60 80 100 110 90 70 400lfm 200lfm 100lfm natural convection efficiency vs output load ( dual output ) efficiency vs output load ( single output ) 20 30 40 50 60 70 80 90 load current (%) 100 60 40 20 10 80 efficiency (%) 20 30 40 50 60 70 80 90 efficiency (%) load current (%) 100 60 40 20 10 80 efficiency vs input voltage ( dual output ) efficiency vs input voltage ( single output ) 50 60 70 80 90 100 input voltage (v) nom low high efficiency (%) 50 60 70 80 90 100 input voltage (v) nom low high efficiency (%) miw1500 series rev:0 2005/04 minmax 5
test configurations input reflected-ripple current test setup input reflected-ripple current is measured with a inductor lin (4.7uh) and cin (220uf, esr < 1.0[ at 100 khz) to simulate source impedance. capacitor cin, offsets possible battery impedance. current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 khz. peak-to-peak output noise measurement test use a cout 0.47uf ceramic capacitor. scope measurement should be made by using a bnc socket, measurement bandwidth is 0-20 mhz. position the load between 50 mm and 75 mm from the dc/dc converter. design & feature considerations maximum capacitive load the miw1500 series has limitation of maximum connected capacitance at the output. the power module may be oper ated in current limiting mode during start-up, affecti ng the ramp-up and the startup time. for optimum performance we recommend 220uf maximum capacitive load for dual outputs and 470uf capacitive load for single outputs. the maximum capacitance can be found in the data sheet. overcurrent protection to provide protection in a f ault (output overload) condition, the unit is equipped with internal current limiting circuitry and can endure current limiting for an unlimited duration. at the point of current-limit incepti on, the unit shifts from voltage control to current control. t he unit operates normally once the output current is brought ba ck into its specified range. input source impedance the power module should be connected to a low ac-impedance input source. highly inductive source impedances can affect the st ability of the power module. in applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low equivalent series resistance (esr < 1.0[ at 100 khz) capacitor of a 8.2uf for t he 5v input devices, a 3.3uf for the 12v input devices and a 1.5uf for the 24v devices. output ripple reduction a good quality low esr capacitor placed as close as practicable across the load will give the best ripple and noise performance. to reduce output ripple, it is recommended to use 3.3uf capacitors at the output. miw1500 series 6 minmax rev:0 2005/04 +out -out +vin -vin dc / dc converter load battery + lin + cin to oscilloscope current probe +out -out +vin -vin dual output dc / dc converter resistive load scope copper strip cout com. scope cout +out -out +vin -vin single output dc / dc converter resistive load scope copper strip cout + +out -out +vin -vin dc / dc converter load dc power source + - cin +out -out +vin -vin load dc power source + - cout com. dual output dc / dc converter +out -out +vin -vin load dc power source + - cout single output dc / dc converter
thermal considerations many conditions affect the thermal performance of the power module, such as orientat ion, airflow over the module and board spacing. to avoid exceeding the maximum temperature rating of t he components inside the power module, the case temperatur e must be kept below 90c. the derating curves are det ermined from measurements obtained in an exper imental apparatus. miw1500 series rev:0 2005/04 minmax 7 dut position of air velocity probe and thermocouple 50mm / 2in air flow 15mm / 0.6in
the miw1500 converter is encapsul ated in a low thermal resistance molding com pound that has excellent resistance/electrical characteristics over a wide temperatur e range or in high humidity environments. the encapsulant and unit case are both rated to ul 94v-0 flammability specifications. leads are tin plated for improved solderability. nc: no connection +vin +vin 23 ul94v-0 : flammability +vin +vin 22 common -vout 16 12.4g : weight +vout +vout 14 -vout nc 11 non-conductive black plastic : case material common no pin 9 -vin -vin 3 1.25*0.80*0.40 inches -vin -vin 2 31.8*20.3*10.2 mm : case size dual output single output pin physical characteristics pin connections {0.002 {0.05 pin x.xxx{0.005 x.xx{0.13 x.xx{0.01 x.x{0.25 inches millimeters tolerance dual output single output 31.8 [1.25] 10.2 [0.40] 20.3 [0.80] bottom 4.5 [0.18] side 23 11 14 22 23 16 9 0.50 [0.020] 2.54 [0.100] 15.22 [0.600] 2.5 [0.10] 4.5 [0.18] connecting pin patterns top view ( 2.54 mm / 0.1 inch grids ) mechanical dimensions miw1500 series 8 minmax rev:0 2005/04
|
